Cabin Guide

🪵 Before You Begin:

• The fireplace should always be set to “Pilot” when not in use.

• The control knobs are located on the panel beneath the logs.
  
  

🔥 To Turn On the Fireplace (Normal Use):

1. Make sure the far-right knob under the logs is turned to “On.”

2. Go to the right side of the fireplace mantle and turn the timer switch to your desired time.

   • The fireplace will turn on automatically and shut off when time runs out.

3. When you’re done for the day, turn the far-right knob back to “Pilot.”

   • Do not turn it all the way to “Off.”

💡 During winter, everything is already set up. You’ll usually just need to turn the timer on the right side of the mantel to start the fire.

⚠️ If the Fireplace Does NOT Turn On:

First check if the Pilot Light is Lit

• Look for a small flame in the center under the logs.
  
  

✅ If the pilot is lit

• Make sure the far-right knob is set to “On.”

• Ensure the far-left toggle switch (next to the knob) is set to “Off.”

• Then rotate the timer switch on the right side of the mantel to start the fire.
  
  

❌ If the pilot is not lit

1. Make sure the gas is turned on — use the gas key (turn counter-clockwise) to open the gas valve.

2. Turn the far-right knob to “Pilot.”

3. While pressing and holding that knob in, press the igniter button (far-left button) until it clicks.

   • Repeat until you see the pilot flame light up.

   • You can also use the long lighter in the drawer under the coffee maker if needed.

4. Once the pilot is lit, turn the far-right knob to “On.”

5. Rotate the timer dial on the mantle to start the fire.
   
   

When Finished:

• Always turn the far-right knob back to “Pilot” (not “Off”) when not in use.

• Leave the timer in the off position.

The hot tub should be ready for you to enjoy anytime!
 

If it ever stops heating properly, it may have been switched into Eco Mode by mistake.
Follow these quick steps to return it to normal heating mode:

🔧 If the Water Isn’t Heating

1. Press the Temp button immediately followed by the Light button.

2. The display will show one of three modes: SL, EC, or St.

   • SL (Sleep) and EC (Eco) will prevent the water from heating fully.

   • You want “St” (Standard) mode.

3. If it doesn’t say “St,” press Temp then Light again until “St” appears.

4. Wait about 10 seconds for the setting to save.

   • (Note: the “t” in “St” may look a bit unusual — that’s normal.)
     
     

🔓 Opening the Lid

1. Start from the left side of the stairs and slowly fold the cover halfway over to the right.

2. Then walk around to the right side and gently pull the lid the rest of the way off.

3. Always close and secure the lid after use to keep the water clean and warm.

💡 Tip: When finished, set the tub back to “EC” (Eco) mode to maintain temperature efficiently between uses. 

⚠️ Hot Tub Safety 

Please enjoy the hot tub safely and responsibly.

• Supervise children at all times — the hot tub is not recommended for kids under 5.

• No glass, bottles, or sharp objects near or in the hot tub (broken glass = $500 cleaning fee).

• Do not add soaps, oils, or bubbles — they damage filters and heaters.

• No diving, jumping, or horseplay.

• Avoid use if you’re under the influence of alcohol or medication that causes drowsiness.

• Limit soak time to 20–30 minutes and stay hydrated.

• Always rinse off before use and close the lid securely afterward to keep the water clean and warm.

Enjoy a movie night at Creekside Cabin! Follow these quick steps:

▶️ To Watch

1. Turn on the projector.

2. Using the Roku remote, press the Home button to go to the main menu.

3. Turn on the soundbar.

4. Press the Bluetooth button on the soundbar.

   • The projector and soundbar should connect automatically.
     
     

🔊 If the Sound Doesn’t Play

1. Make sure the soundbar is powered on and Bluetooth is enabled.

2. On the Roku, go to:
   Settings → Remotes & Devices → Wireless Headphones → Vizio V51 → Connect

⚡ When Finished

• Please power off the projector to prevent the bulb from burning out.

• Turn off the soundbar.
  
  

🍿 Now grab a blanket, get comfy, and enjoy your movie night!

Enjoy grilling on the deck — just follow these quick steps:

✅ To Start

1. Check the gas valve coming from the deck — it should be vertical (open).

2. On the right side of the grill, turn the red timer knob to set how long you want the gas to flow.

3. Press and turn the burner knobs to “Light,” then press the ignite button to start the flame.
   
   

⚠️ If It Doesn’t Light

• Turn the burner off.

• Wait 30 seconds to let the gas air out.

• Try lighting again.
  
  

🔒 When Finished

• Turn all burner knobs to OFF.

• Turn the deck valve to horizontal (closed) to shut off the gas.

• Clean the grill surface after it cools.

🧽 To Clean

1. After cooking, turn off all burners and let the griddle cool slightly (still warm, not hot).

2. Use a grill scraper or paper towels to remove food and grease.

3. Wipe clean with a light coat of oil to protect the surface and prevent rust.

4. Once cool, make sure the gas valve is turned off and the cover is on.

Enjoy a little retro fun — the arcade is easy to use and perfect for all ages!

👤 Single Player Mode

1. Use the right-hand controller.

2. Slide the power switch above the joystick to “On.”

3. Use the joystick to scroll and select your game.

4. Press the bottom-left white button, then press “Start Game.”

   • Some games may require pressing “Start” twice.
     
     

👥 Two-Player Mode (available on select games)

1. Player 2 uses the left joystick.

2. Player 2 presses the bottom-left white button.

3. Player 1 then presses their “Start” button.

4. The game will automatically alternate turns between players.
   
   

🔙 To Return to Main Menu

Hold the Start button for 5 seconds.

Our backyard zipline is one of the most loved features at Creekside Cabin — it’s designed for kids only and meant to create fun outdoor memories while keeping everyone safe.

✅ Before You Ride

1. Adult supervision is required at all times.
   An adult must be present to help adjust and monitor each ride.

2. The zipline seat height can be adjusted for comfort and safety.
   Adjust the seat height and make sure your child’s feet can touch the ground before starting.
   
   

3. Use the safety belt and harness every time.
   The safety belt is located in the cabinet under the kitchen sink.

   • Clip and tighten the strap securely around your child.

   • Ensure it’s attached to the zipline carabiner before riding and adjusted to their height.
     
     

4. Weight limit: 50 lbs maximum.
   Only one rider may use the zipline at a time.
   
   

5. Check surroundings — confirm the landing area is clear and free of obstacles.
   
   

🎢 During the Ride

• Hold the handles firmly with both hands.

• Sit on the seat and enjoy the gentle ride across.

• Never stand, twist, or jump from the line while in motion.

🧺 After You’re Done

1. Carefully remove the safety belt and return it to the cabinet under the sink.

2. Double-check that the zipline seat and cable are secure and not tangled.

3. Adults should ensure all equipment is safely stored and the area is clear.
   
   

⚠️ Safety Reminders

• Adults are not permitted to ride the zipline or play equipment.

• Misuse or unsafe behavior may result in injury so be safe!!! 

• Have fun — but always make safety the top priority!